customer service hotline : 86-755-86026786

stock code:603063

Banner
products and solutions
Low-voltage Ride-through domain grid simulation system

Low-voltage Ride-through domain grid simulation system

contact now

Low-voltage Ride-through Simulation System

Features:

1. Low-voltage ride-through simulation system is able to faithfully simulate the various low-voltage faults of the power grid, including the grid voltage symmetrical dip and asymmetrical dip.
2. The dip curve is compliant with the regulations of the newest national standards, therein, the dip amplitude and dip duration of each stage can be set flexibly.

As shown in the figure below: In the figure, the solid line is the contour of the work area of the turbine and the dashed line is the example of dip curve for actual test.



If you want to know some information about our company,pls check our website: www.hopewindelectric.com

Related Product
  • Domain Grid Simulation System 2.5MW Wide Frequency Domain Grid Simulation System

    2.5MW Wide Frequency Domain Grid Simulation System Features: 1. Independent control of three phase voltage and high overload capacity, assuring simulation of various grid variation and low voltage faults. 2. 32-bit DSP-based real time and intelligent control, with high accuracy of waveform and slew rate control, excellent steady and dynamic performance. 3. Simple and intuitive HMI, providing higher operation efficiency. 4. Support 60Hz grid simulation for exporting wind turbine set testing. If you want to know some information about our company,pls check our website: www.hopewindelectric.com

  • Wide Frequency Domain Grid Simulation System 7.5MW Wide Frequency Domain Grid Simulation System

    7.5MW Wide Frequency Domain Grid Simulation System Features: 1. Independent control of three phase voltage and high overload capacity, assuring simulation of various grid variation and low voltage faults. 2. 32-bit DSP-based real time and intelligent control, with high accuracy of waveform and slew rate control, excellent steady and dynamic performance. 3. Simple and intuitive HMI, providing higher operation efficiency. 4. Support 60Hz grid simulation for exporting wind turbine set testing.   If you want to know some information about our company,pls check our website: www.hopewindelectric.com

  • Main Control System Main Control System

    Main Control Electric System Hopewind has the design, production and testing capacities of main control electrical system. According to the electrical topology of the wind turbine unit, we can provide single cabinet type and make the design and production of the double cabinet type package plan. The system meets the corresponding standards of GB 7479-2010/IEC 60446:2007, GL2010 and so on. The main control cabinets designed and manufactured by Hopewind have all passed the internal type tests, such as ESD, radiated electromagnetic field immunity, insulation resistance, high voltage endurance, vibration、protection, high and low temperature, lightning protection, and overall machine whole functions on-site operation test. Hopewind can customized the cabinet size according to the customer requirements. If you want to know some information about our company,pls check our website: www.hopewindelectric.com

  • Commercial High Power Inverter Commercial High Power Inverter

    (30K/33K/36K/40K/50K/60K)

  • Engineering Type variable frequency drive manufacturers HD8000 Series Medium Voltage Engineering Type variable frequency drive manufacturers

    HD8000 Series Medium Voltage Engineering Type Variable Frequency Drive System Product Introduction: 1.The "system level" design and modularization units of accessory engineering, to facilitate the expansion of power and customized engineering combination, to meet meet the flexibility of application and integration of system. 2. Engineering reliability design concept, using IGCT and crimping power module, with two-level, three-level, five-level and seven-level topology; fewer devices, high reliability. 3. With our rich range of products and solutions, can provide a direct replacement for CC, LCI products; grid level supporting 1.65kV, 3.3kV, 6.6kV, 10kV, with 3MW-90MW power coverage. 4. Complete rectifier front-end, including basic rectifier, intelligent feedback rectifier and AFE rectifier; can providing a common bus two-quadrant/four-quadrant transmission system according to customer demand. 5. Ultra high power density, minimal footprint. 6. Use of deionized water cooling scheme, internal heat dissipation using the wind-water heat exchanger; high protection level, up to IP65. 7. Can be seamlessly connected with the mainstream PC, in addition to supporting the mainstream Profibus, CANopen, ModBus RTU protocol, but also supports TCP/IP, CC-Link, DeviceNet and other protocols. 8. Excellent control performance; when sudden increase of rated torque, the current response time is about 5ms under the torque control mode. 9. Strong adaptability of the grid to support a wide range of input power grid; better adaptability of unbalanced grid and harmonic distortion grid. 10. The product can be suitable for asynchronous induction motor, permanent magnet synchronous motor and electric excitation synchronous motor. 11. Providing a quick debugging tool hopeInsight, can achieve intelligent wizard, graphical configuration, fault recording and 12-channels background oscilloscope ,for more convenient network debugging. 12. Hopewind Cloud Data Management Services be used to achieve "zero" distance monitoring, providing customers with advanced data analysis and diagnostic services, reducing unplanned downtime. 13. Products can be widely used in metallurgical steel rolling, oil and gas transportation, mining machinery, marine equipment, test bench, offshore wind power, pumped storage and other industrial fields. If you want to know some information about our company,pls check our website: www.hopewindelectric.com

  • Dry-type Transformer Dry-type Transformer

    (1.0MW~6.25MW)

  • Wind Power Inverter Monitoring Software hopeInsight Wind Power Inverter Monitoring Software

    hopeInsightTM Monitoring Software hopeInsightTM monitoring software, which is commonly known as the background software, is suitable for all products of our company. The software has a large number of professional debugging functions, such as batch parameter setting, fault data download and waveform analysis, high speed oscilloscope and a large number of editing functions, etc. The software supports serial port or Ethernet, so the software is able to maintain converters through the serial communication, also in the central control room through the Ethernet. hopeInsightTM can be used for a single converter monitoring, also be used as a component of hopeViewTM. Taking the converter as an example, the working schematic diagram is as follows:

Copyright © Shenzhen Hopewind Electric Co., Ltd. All Rights Reserved.dyyseo.com

online service

service

online service